Відео

This is an awesome lift! But I was wondering with the wheels on the lift itself to make it portable and easier to move, once the vehicle is lifted what stops it from rolling on a smooth floor surface? Do the wheels just not move once there is weight on them?

mirrors seeing uranus! 👨‍🚀🪞👩‍🚀🪩🧑‍🚀🌐

Very well explained!

I powder coat at 250 20 mins

Do they mak sure the lift raises evenly not lopsided.....after a couple of years

I installed this and it has already broke twice. I know this is going to leave me stranded with the brake locked on. I am just going to eat the cost and remove it and go back to the foot brake. You also can not use it if the ignition is on. You can never uses it if you really had an emergency while driving. It is a real neat idea and mostly works. It is just one more part to break and leave you stranded,, and it did break twice.

Could you tell me where I can buy this lift?

Try using a fish tank pump for adjitation that will help in hard to get areas

👍👍👍

should be shown in all shops

i agreed! buy better, buy less. I buy USA quality products when possible but it’s very hard to find these days. I buy Snap-On USA tools even though it costs a lot more.

what size air compressor is recommended?

Stands to reason

Great tutorial, thank you👍👍👍

If you want to be different than all the other utube wannabes don’t brag on your self 😊😊

Will that lift a softail high enough to take the wheel off?

Does this lift the bike enough to remove either or both wheels?

Any details about the recommended concrete pad?

Buying this

Love this idea .

I would like info

I have never uploaded a video now to and I’m a very handy guy that have done a million diy at home . But I don’t do videos on, anyways I appreciate someone like you doing video and give your opinion on things never do criticize because I done no videos myself. Take the good advice and the trolls criticism let them be , they will never prospered that’s why they criticize. I follow a guy name COLTS WAY and all though he does what I do for a living (LINEMAN) he says it very clear . I don’t care what you think or say that’s his way on doing it. Great video and I appreciate it. You gain another follower. Thx

I have a set of Forgeline GA1R for my STI. Everything this guys said was 100% on point. I can't recommend Forgeline enough.

Can I sale in kenya

My thumbs up is only for me to keep track on what I have watched on the various car videos I have watched. But deep down I wanted to give a thumbs down for your bad experience..... but a thumbs ups for sharing, soooo thanks for sharing Ian. I enjoy what you share🇦🇺

As I began shopping for a lift and realized that going from 10k to 12k switches from direct drive to chain drive, I balked a bit as I want/need the 12k. Then I thought, how are hundreds of thousands of fork-lifts (which I used to use in the workplace) doing their lifts? With chain drive. It's not the end of the world!

Well that sucks. Won’t be buying those hinges. I have no doubt you will get it straightened out

i would think when you buy a carbon hood that there would be a disclaimer on what hinges they reccomend. Good luck man. put a steel hood on it. so id moreso blame the hood guy especially since he said " he sees this all the time"

Maybe the hood is junk .....

just curious about your car do you drive it without any paint coatings on it and do you get many rusty spots showing up

That sucks man. Have you tried: A. Removing the gas struts just to see what happens? B. Placing a 1/8 inch thick shim between the hood hinge and the hood on just the back bolt closest to the firewall to raise the back edge up and readjusting? C. Trying the hood with stock hinges and low tension springs? As for the bowing, I would suggest with the hood bolted to the car and the hood hinge springs removed, latching it in the front, and then placing some sandbags on the hood where it’s bowed up in the direct sunlight to press downward. Hope you get it straightened out.

Remove the hood and turn it upside down bolted to a couple of 2x4's then put a hair dryer or two under it. Make sure you put a stop so that when it goes the other way it wont hyper extend. When you do get it the way you want it I strongly recommend going with a hood prop as even a little pressure pushing up with a hot engine on a hot day when parked will bow it with any amount of gas shock. Just so you know I have been a professional laminator and boat builder for over 40 years, resulting in having built lots of race and street car parts in composite materials.

How do you switch to ALUS mode? When I press the button it skips over ALUS.

Hey man. You mentioned that you lifted your brother Vette. Did you have to place the car more back? I have a C6 and my hoist arms are too long. Two arms are lining up with the lift points but only between the two portions of of the arm (main part and extending part)

I found the Black Diamond coal slug works on everything Especially on rust

How much for you to build me one lol

If you don't have a sand blaster could you use a chemical strip dip?

Try to make another box like the one you made only use heat guns through holes on all four corners. Slightly tilt to where it creates a vortex. I've always wanted to see the temperature difference on that.

stupid and unsafe

I would have bought this one had it been made in USA - i purchased a Handy RAM (2500 rated capacity) today instead because of country of origin.

Use frame pucks.

Thanks for the quick and concise video on this product.

Great tips! Thanks for sharing!

Thanks for the video. I'd like to see the best option for blasting patio furniture. I have an old hanamint patio set that I'd like to refinish. What's the best gun set up to get off the old coat of paint, what's the best gun set up to repaint it? Thanks

Exactly what I need

Happy 🔧

Excellent with no BS. Thanks for posting this

if you do not want a yellow finish , do you just not dip into Yellow chromate solution ?

Geeze, what a pain it must be to get an engine bolted and unbolted from that monstrosity and its only rated at 2000lbs? Harbor Frieght sells a 2000lb stand and with a little ingenuity, you could fit an electric motor to it to spin it and still probably be at half the cost of a Redline product.

Should have tried copper slag or coal slag although coal slag will imbed itself into the metal.